This hybrid turbo, designed for 2.8 diesel engines, is based on a ready-to-install configuration that requires no modifications to the original d . Depending on the chosen specification, it incorporates a high-flow MFS compressor wheel, a 360° bearing stop and appropriate internal modifications.
Documented applications include theIveco Daily 2.8 TD and theOpel Movano A 2.8 DTI. Compatibility must always be confirmed using the original turbo part number d.
Available upgrades — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing: 360° bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor impeller in order dto adjust the compression capacity and air flow rate dwhilst maintaining a direct-drive configuration d.
Stage 2
Compressor impeller: MFS high-flow oversized
d’ intake housing: Reprofiled for accommodate the new impeller
Thrust bearing: 360° bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a reprofiled housing d’admission. This modification is designed to increase the air displacement capacity dunder appropriate operating conditions.
Stage 3
Compressor impeller: MFS high-flow oversized
dintake housing: Reprofiled for accommodate the new impeller
Thrust bearing: 360° bearing
Turbine impeller: High-flow oversized
Turbine casing: Reprofiled for ly to accommodate the new impeller
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification is carried out on both the compressor and turbine sides. The oversized impellers require both housings to be re-profiled and may alter the air flow rate das well as the behaviour of the turbocharger.
What is a hybrid turbo?
A hybrid turbo retains an architecture compatible with the intended installation whilst incorporating internal modifications. Depending on the modification stage, these may involve the compressor impeller, the turbine impeller, the housings, the thrust bearing and the rotor balancing.
The aim is dto adapt the compression capacity and the air flow rate d. A hybrid turbo is not defined solely by the appearance of its impeller: its geometry, dimensions and the adaptation of its casings are crucial.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in airflow d. A standard MFS wheel may retain a geometry equivalent to that dof the original.
An MFS wheel Performance can be given a geometry adapted to the modification. On this product, the wheel shown is made of forged aluminium and has dimensions larger than those dof the original.
A standard MFS impeller can be just as polished as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. A higher airflow can only be fully utilised with appropriate engine tuning.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air admitted by the engine. Its diameter, profile, height, width and blade arrangement all influence its aerodynamic behaviour. The result also depends on the casings, the turbine wheel, the boost pressure and the engine mapping. A larger wheel does not automatically guarantee a better result and may alter the response time.
Reliability and balancing of the hybrid turbocharger
The documented 360° bearing stop helps to distribute the axial forces to which the rotating assembly is subjected. It does not, however, replace d’proper lubrication or d’correct installation.
The rotor is balanced at high speed, up to 150,000 rpm, on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses, without compensating for any installation faults d, contamination or insufficient oil supply.
Engine reprogramming and preparation
The operation dof a hybrid turbo requires appropriate engine management. The mapping, boost pressure, injection, exhaust and cooling must be checked or adjusted according to the modification. The wastegate setting must be adjusted when reprogramming the ECU. The clutch, transmission and other vehicle components must also be taken into account.
Turbo specifications
Documented manufacturer part numbers
49135-05010
49135-05000
49135-05030
49135-05050
53149706445
53149806445
53149886445
53149906445
OEM part numbers and other documented part numbers
99450704
99450703
7410216v
99455591
9945569
99460981
99466793
451246
Compatible vehicles and assignments
Iveco
Daily 2.8 TD — 103 hp
Engine variants 2.8 TD — from 1996, end date unspecified
Engine code: not specified
Opel
Movano A 2.8 DTI — 113 hp
Engine 2.8 DTI — from 1998, end date unspecified
Engine code: not specified
Additional technical specifications
Product type: Hybrid Turbo
Engine: Diesel 2.8
Installation: plug & play configuration, without modification to the original dset-up
Power ratings stated: 103 / 115 hp in the title; 103 hp and 113 hp in the documented specifications
Engine code: Not specified
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d’installing the turbo. Check the lubrication circuit, the oil supply and return d’as well as the cleanliness of the pipes.
Check the intake for foreign objects. Prime the system in accordance with the applicable recommendations and follow the vehicle manufacturer’s instructions.
A lubrication fault that is not rectified may lead to further failure of the turbocharger.
How do you identify the correct turbo?
Check the part number marked on the original turbo d, then compare it with the manufacturer and OEM part numbers in this data sheet.. Also check the make, model, generation, engine type, power output,Year, and the engine code where available. An identical engine specification is not always sufficient to confirm compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original dturbo with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your turbo’s nameplate.